Welcome, Guest. Please login or register.
Did you miss your activation email?
November 21, 2024, 10:37:04 PM
Home Help Search Login Register
News: Ceriatone Forums are up and running!!!
 
Guests please register
Note: If you want to help you can donate to keep the forums alive.



Do you want to advertise on this forum ? Send me a private message.

Amplified Parts
+  Ceriatone Forum
|-+  Ceriatone
| |-+  Overtone
| | |-+  ots troubles		 « previous next »
Pages: 1 2 [3] 4 Go Down Print
Author Topic: ots troubles  (Read 27876 times)
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #30 on: November 17, 2009, 09:02:49 AM »
Quote from: RiffRaff on November 17, 2009, 08:54:14 AM
Found it, I pinched a wire between the standoff and mainboard
I built listening probe
(a pair of aligator clips, a 1/4" jack, a .047uF/400V (or more) cap and some wire. You connect a wire from an aligator clip to the ground connection on the jack, the cap to the other clip and the other side of the cap to the hot lead on the jack.)
then hooked that jack via 1/4" cable to another amp
Plugged in a tone generator to the OTS input and tried to trace the sound
but I could not get a signal from the tip of the input jack on the OTS
The listening probe worked fine when the tone generator was hooked directly to the aligator clips but not thru the input jack of the OTS
sssoooo unless I've wired the input jacks wrong which I've checked several times and even rewired again there must be a short to ground on the inputs
Is this correct?
I'm just guessing......remember I'm a newbie

Tim


Yes, with not jack plug connected to the input, the input jack (22k into V1a, pin2) is shorted to ground.
Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #31 on: November 17, 2009, 10:58:32 PM »
Whats the current status ?? is the amp operational ?
Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
RiffRaff
Jr. Member
**
Offline Offline

Posts: 50


View Profile
« Reply #32 on: November 19, 2009, 04:08:24 AM »
Sorry just got back from a ZZTop concert
No the amp has no sound as of yet
Nik say's that the input is wired correctly
so I'm stumped
Logged
hywelg
Hero Member
*****
Offline Offline

Posts: 896


View Profile
« Reply #33 on: November 19, 2009, 09:03:51 AM »
Time to take it to a tech?
Logged
mcinku
Administrator
Hero Member
*****
Offline Offline

Gender: Male
Posts: 1084



View Profile WWW
« Reply #34 on: November 19, 2009, 09:15:12 AM »
Quote from: hywelg on November 19, 2009, 09:03:51 AM
Time to take it to a tech?

+1
Logged
My website

TW Express build
BM HRM build
Prinzetone build
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #35 on: November 19, 2009, 10:10:22 AM »
+1 from me as well

However, I have one small suggestion you could try.

For testing purpose, as per the attached picture, solder a wire direct from V1 out to the power amp in. This way you will find out if the problems are related to the relays or send/return jacks. Just an idea.

* 1_wire_Clean_direct_to_output.jpg (275.08 KB, 1277x958 - viewed 617 times.)
Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
RiffRaff
Jr. Member
**
Offline Offline

Posts: 50


View Profile
« Reply #36 on: November 19, 2009, 03:40:06 PM »
closest amp tech is probably 300 miles from where I live
I've been talking to Nik and he asked if the tip of the input jack was shorted to ground
With a 1/4 inch cable inserted I have continuity to the chassis
Logged
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #37 on: November 19, 2009, 05:18:23 PM »
Quote from: RiffRaff on November 19, 2009, 03:40:06 PM
closest amp tech is probably 300 miles from where I live
I've been talking to Nik and he asked if the tip of the input jack was shorted to ground
With a 1/4 inch cable inserted I have continuity to the chassis

Solder an alternative jack direct to pin 2 on V1 (and disconnect the existing input wire)

If this doesn't work, use the 'yellow wire' mod I've pictured above.
« Last Edit: November 19, 2009, 05:25:36 PM by bluesfendermanblues » Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
RiffRaff
Jr. Member
**
Offline Offline

Posts: 50


View Profile
« Reply #38 on: November 19, 2009, 06:34:22 PM »
Well I feel kinda dumb
I have all the wires that are spliced into the shielded wire hooked up to the main conductor wire instead of the shielding
I'll redo them after work and let you know how it goes
Logged
RiffRaff
Jr. Member
**
Offline Offline

Posts: 50


View Profile
« Reply #39 on: November 20, 2009, 12:55:56 AM »
Ok
Fixed all the wires and we had sound
Played it for about ten minutes and it just quit suddenly
all the voltages are good and the bias
Any ideas?
Logged
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #40 on: November 20, 2009, 07:02:46 AM »
Quote from: RiffRaff on November 20, 2009, 12:55:56 AM
Fixed all the wires and we had sound

What wires??
Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
RiffRaff
Jr. Member
**
Offline Offline

Posts: 50


View Profile
« Reply #41 on: November 20, 2009, 07:36:05 AM »
From the post above

"Well I feel kinda dumb
I have all the wires that are spliced into the shielded wire hooked up to the main conductor wire instead of the shielding
I'll redo them after work and let you know how it goes"

It was working good , all the switches and pots did what they were supposed to
It did have an ac hum that wasn't that bad, not sure if it is from this old building I live in or wire placement
Fuses are good, all the voltages are good
it just quit working
I used to get a small click or pop when I turned the standby switch on but now I get nothing
Logged
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #42 on: November 20, 2009, 09:01:33 AM »
Quote from: RiffRaff on November 20, 2009, 07:36:05 AM
From the post above

"Well I feel kinda dumb
I have all the wires that are spliced into the shielded wire hooked up to the main conductor wire instead of the shielding
I'll redo them after work and let you know how it goes"

It was working good , all the switches and pots did what they were supposed to
It did have an ac hum that wasn't that bad, not sure if it is from this old building I live in or wire placement
Fuses are good, all the voltages are good
it just quit working
I used to get a small click or pop when I turned the standby switch on but now I get nothing

blown fuse?
Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
RiffRaff
Jr. Member
**
Offline Offline

Posts: 50


View Profile
« Reply #43 on: November 20, 2009, 08:00:44 PM »
Fuses are good
Here's something I noticed
When I turn up the ratio and level I can here an ac hum coming from inside the chassis
sounds like it's coming from the pots themselves but I'm not sure
and when I touch one of the output tubes it get louder
Logged
hywelg
Hero Member
*****
Offline Offline

Posts: 896


View Profile
« Reply #44 on: November 20, 2009, 08:42:25 PM »
Check your socket wiring, what about all the checks you made initially have you redone them? ie line level in at FX loop, FX loop out to another amp, bias still OK etc. trouble shooting is just a matter of being thoroughly methodical and breaking the testing down into bits to eliminate various possibilities.

I'd hesitate to suggest it but consider chopsticking various signal path connections, based on your results from the fx loop tests above. If you don't know what I mean then you probably shouldn't do it, it is dangerous.
Logged
Pages: 1 2 [3] 4 Go Up Print 
« previous next »
Jump to:  


Login with username, password and session length

Powered by MySQL Powered by PHP Powered by SMF 1.1.12 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!

CeriaTone Forum is not afiliated with Ceriatone Amplifications. The CeriaTone and name, logo and related trademarks and service marks, owned by CeriaTone. , are registered and/or used in the U.S. and many foreign countries. All other trademarks, service marks, and trade names referenced in this site are the property of their respective owners.