What the #@!%&*%#????

dannysgrandpa
Jr. Member

Offline

Gender: Male

Posts: 64

Life is good here! God is good...all the time!

What the #@!%&*%#????

« on: August 16, 2008, 06:00:54 AM »

Hey all, I finished my OTS tonight and put the tubes in, hooked up a speaker and turned on the mains and all the tubes glowed. Grin

Waited a couple of minutes and, with all the controls set at zero, I flipped the standby to "on". Instantly, a very loud and high pitched squeal came from the speaker. I immediately turned to standby and changed the impedance switch and tried again. This time the sound was low and also very loud. turned the thing off and came here. Help!!!!! Cry


	Logged

Make a joyful noise...that is smooth, tight and punchy! I believe that God likes tube tone.
Certified IPC Master Trainer: 610G, 620C, J-STD-001G/Space, 7711C/7721C. Hands on soldering trainer, inspection trainer and Electrostatic Discharge instructor.

bluegate
Jr. Member

Offline

Posts: 63

Re: What the #@!%&*%#????

« Reply #1 on: August 16, 2008, 08:21:06 AM »

This happened to most of us...

Change the two wires from OT to the two tubes.
That should do the trick.


	Logged

dannysgrandpa
Jr. Member

Offline

Gender: Male

Posts: 64

Life is good here! God is good...all the time!

Re: What the #@!%&*%#????

« Reply #2 on: August 18, 2008, 05:03:23 AM »

Yep, got rid of the squeal, thanks. Now I've got a bigger problem. I plugged in my 335 and no sound!!!!!! Nothing, zip, zilch, nada!! I checked the input jacks for signal, got it. Checked the pins on the tubes and could hear the little tick through the speaker when I touched each pin tab. I even went so far as to plug my guitar into the return jack of the effects loop and could play through the power section which, by the way, was quiet and absolutely noise free. So...now what?? Any ideas? Thanks in advance, Bill


	Logged

AdrianJ
Full Member

Offline

Gender: Male

Posts: 207

Re: What the #@!%&*%#????

« Reply #3 on: August 18, 2008, 09:16:32 AM »

Have you tried new preamp tubes?


	Logged

White Rose Guitars

Steven_nl
Sr. Member

Offline

Gender: Male

Posts: 473

Re: What the #@!%&*%#????

« Reply #4 on: August 18, 2008, 02:12:32 PM »

are you sure the footcontroler switches on the back of the amp are set properly?


	Logged

bluegate
Jr. Member

Offline

Posts: 63

Re: What the #@!%&*%#????

« Reply #5 on: August 20, 2008, 07:35:08 AM »

Check the wires on the input.
The drawing is a little confusing to look at, you see the input at a certain view that a
mistake is easy to make.

Check if the tip of the jack is connected to the input of V1 and you didn't make a ground
mistake that leads the signal direct to ground.

Also the chassis inputs have connections on each side, but only one side will be active
when you plug-in. So check that you've wired the correct side.


	Logged

ic-racer
Full Member

Offline

Posts: 104

Re: What the #@!%&*%#????

« Reply #6 on: August 20, 2008, 05:37:31 PM »

Relays plugged in correctly? Wired correctly? Should be some little mistake somewhere. Good to know the power section is fine, that narrows it down a lot.


	Logged

Pages: [1]

« previous next »

	Welcome, Guest. Please login or register. Did you miss your activation email? November 22, 2024, 01:07:23 PM

News: Ceriatone Forums are up and running!!! Guests please register Note: If you want to help you can to keep the forums alive. Do you want to advertise on this forum ? Send me a private message.