Welcome, Guest. Please login or register.
Did you miss your activation email?
November 22, 2024, 02:22:00 AM
Home Help Search Login Register
News: Ceriatone Forums are up and running!!!
 
Guests please register
Note: If you want to help you can donate to keep the forums alive.



Do you want to advertise on this forum ? Send me a private message.

Amplified Parts
+  Ceriatone Forum
|-+  Muchless
| |-+  DC 30
| | |-+  OT Pre amp tube sheild		 « previous next »
Pages: [1] Go Down Print
Author Topic: OT Pre amp tube sheild  (Read 13703 times)
XB9R
Newbie
*
Offline Offline

Gender: Male
Posts: 9


View Profile
« on: June 29, 2011, 10:50:02 AM »
Has anybody bothered to put the shield in between the OT and the Preamp tubes? Or is it quite enough with out it? wondering if any body had any pics of a build with the sheild installed. read somewhere that this could have benefits to reduce hum, and the kits look like they are now supplied with a piece of thin aluminimum for this purpose, well mine was anyway.
Logged
charmcolors
Newbie
*
Offline Offline

Posts: 2


View Profile
« Reply #1 on: June 30, 2011, 07:46:22 PM »
I did, worked great on reducing noise
Logged
XB9R
Newbie
*
Offline Offline

Gender: Male
Posts: 9


View Profile
« Reply #2 on: July 01, 2011, 10:25:23 AM »
Thanks Charmcolors, did you put yours the full lenght of the preamp tubes or did you only make it slightly larger than the width of the OT, Like what Nik has done on the StrayCat model?
Logged
charmcolors
Newbie
*
Offline Offline

Posts: 2


View Profile
« Reply #3 on: July 15, 2011, 04:25:47 AM »
Just like what nik did on the straycat
Logged
ampkits
Administrator
Sr. Member
*****
Offline Offline

Posts: 325


View Profile
« Reply #4 on: December 30, 2011, 05:47:06 PM »


Hi,

The shield is a requirement, I think.

Thanks!

Nik
Logged
XB9R
Newbie
*
Offline Offline

Gender: Male
Posts: 9


View Profile
« Reply #5 on: March 15, 2012, 07:40:57 AM »
If your in any doubt regarding the shield between the OT and Pre amp tubes just put it in, its easy enough to do before you get to far through the wiring. I ran the DZ30 amp without it to start with then put it in later, I really didn't notice any difference in noise with it in or out, wonder if its more down to lead dress than anything, maybe just an anomaly, Pic attached where you can see it placed in the amp.

* 2012-03-15 20.47.14.jpg (857.96 KB, 1920x2560 - viewed 1035 times.)
« Last Edit: March 15, 2012, 07:55:55 AM by XB9R » Logged
g_agnew
Newbie
*
Offline Offline

Posts: 9


View Profile
« Reply #6 on: March 29, 2012, 08:59:52 PM »
I used a standup type OT so I guess that's why I didn't need the shield.  The only issue I had was a slight hum caused by running the two wires from the board to the Master pot too close together.  Once they were moved apart the amp was fine. I now have one of them cable tied to the mounting hardware for the power supply board. No chance of the hum creeping back in!!
Logged
Gruffnutz
Newbie
*
Offline Offline

Posts: 6


View Profile
« Reply #7 on: April 06, 2012, 10:01:58 PM »
I did mine a little differently to provide some shielding for the FX loop wires as well...
Logged
cmoore
Sr. Member
****
Offline Offline

Gender: Male
Posts: 351


View Profile
« Reply #8 on: April 07, 2012, 02:54:40 AM »
Hey.....you did a nice job.
Hope it sounds as good as it looks.
Well Done
Logged
Gruffnutz
Newbie
*
Offline Offline

Posts: 6


View Profile
« Reply #9 on: June 27, 2012, 08:34:04 PM »
Quote from: cmoore on April 07, 2012, 02:54:40 AM
Hey.....you did a nice job.

Thanks!   Wink

Quote from: cmoore on April 07, 2012, 02:54:40 AM
Hope it sounds as good as it looks.

It does.   Grin   I've tweaked a few components to even out the channel volume a bit (for my settings), improve the 'Cut' control and to get the PI / Master performing as I'd like.

Transformers are Drake AC-30.

Just building some high voltage transistor buffers / remote switchers for the loops now...
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  


Login with username, password and session length

Powered by MySQL Powered by PHP Powered by SMF 1.1.12 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!

CeriaTone Forum is not afiliated with Ceriatone Amplifications. The CeriaTone and name, logo and related trademarks and service marks, owned by CeriaTone. , are registered and/or used in the U.S. and many foreign countries. All other trademarks, service marks, and trade names referenced in this site are the property of their respective owners.