Welcome, Guest. Please login or register.
Did you miss your activation email?
November 22, 2024, 06:43:42 AM
Home Help Search Login Register
News: Ceriatone Forums are up and running!!!
 
Guests please register
Note: If you want to help you can donate to keep the forums alive.



Do you want to advertise on this forum ? Send me a private message.

Amplified Parts
+  Ceriatone Forum
|-+  British Style
| |-+  18 Watt
| | |-+  1St timer need help please.		 « previous next »
Pages: [1] Go Down Print
Author Topic: 1St timer need help please.  (Read 5718 times)
NoPrints
Newbie
*
Offline Offline

Posts: 13


View Profile
« on: April 24, 2008, 10:54:31 PM »
 Ok, so starting out as a 1st time builder, just a few small areas of confusion: 1 The standby switch, on the layout diagram it shows the switch with only 2 posts although the switch supplied has 6. So do I solder 1 to the earth and 1 to the + side?

 #2 The shielded black wire supplied in the kit.  Is this the wire used to run between the 5 posts on the tubes? I am suposing the green is for the #4 post on the tubes?  Or do I use the red and green for this job?

  #3 The diodes; is there a easy way to evaluate thier properties? Is there a colour code available?

  #4 The 4 ohm/ 8ohm wires from the O/T. Where do these go?

   Sorry for the dumb Q's.  Huh?

   Cheerz, Tim.
Logged
ChrisL
Full Member
***
Offline Offline

Posts: 239


View Profile
« Reply #1 on: April 25, 2008, 12:29:49 AM »
Tim,

Before we can answer specifically, please let us know what you are building. 

For the time being a 6 pole standby switch just requires the middle lug and bottom lug on one side wired.  It depends on the circuit where the leads go though.

Shielded wire is NOT for the heater supply.  It's usually reserved for the input section and/or other noise sensitive areas.

Diodes?  Are you sure you don't mean...resistors? 

As for the Output trans wires....again, what are you building; head or combo of what?

There is no such thing as a dumb question.

Cheers,

Chris
Logged
NoPrints
Newbie
*
Offline Offline

Posts: 13


View Profile
« Reply #2 on: April 25, 2008, 01:29:18 AM »
Its an 18w TMB combo model. Are yes resistors  Embarrassed . Yep the switch thing now makes sense to me. Should have thought about that one a bit harder.

  Thanx Chris.
Logged
ChrisL
Full Member
***
Offline Offline

Posts: 239


View Profile
« Reply #3 on: April 25, 2008, 02:54:49 AM »
There are a bunch of resistor color code calculators online.  This one is fun.

http://www.dannyg.com/examples/res2/resistor.htm

If you have the impedance selector it's just 4, 8,16 in the click order of the selector with the master lead going to the tip of the output jack.

If you don't have a selector (ie. combo chassis) the 4 and 8 ohm secondaries are wired to their own individual output jacks.
Logged
NoPrints
Newbie
*
Offline Offline

Posts: 13


View Profile
« Reply #4 on: April 25, 2008, 04:04:22 AM »
 Exellent, Chris !

  Cheerz for the help.
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  


Login with username, password and session length

Powered by MySQL Powered by PHP Powered by SMF 1.1.12 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!

CeriaTone Forum is not afiliated with Ceriatone Amplifications. The CeriaTone and name, logo and related trademarks and service marks, owned by CeriaTone. , are registered and/or used in the U.S. and many foreign countries. All other trademarks, service marks, and trade names referenced in this site are the property of their respective owners.