|
647
|
Ceriatone / Overtone / Re: bit dissapointed
|
on: February 13, 2009, 08:43:48 AM
|
Just think of it this way... a wast majority of people are more than satisfied with this amp, so if you're after the D-tone, this amp will provide it for you no doubt. If you don't know exactly what you want in the first place, than it's possible this amp is not for you. It is also possible that your amp need a touch here and there, so take erwins offer and go see him.  |
|
|
|
|
649
|
Ceriatone / Overtone / Re: HRM Bluesmaster
|
on: February 08, 2009, 08:23:57 PM
|
I found some info about the bluesmaster circuit on the TAG forum and I hope it's OK, if I post these lines here as well... :  Bluesmaster refers to the clean stack and changes in the power amp. The Bluesmaster stack as a little more gain due to its circuit layout. The Bass control is centered around 130 hZ. This gives the bass a softer / spongier feel/attack (to my ears, your ears my be diferent). The middle control centers at around 800 hertz and give a more scooped mid range sound.
The power amp section is roughly the same as a Marshall Plexi (a few component changes). This has reduced negative feedback and gives more PA gain and a large bass response.
The Bluemaster also used a completed different boost arrangement that simply lifts the entire tone stack off of ground. This give a HUGE amount of boost, especially in the lower registers. This boost system also tends to roll the high end off just a little bit (6 to 8 dB) as compared to the bottom end.
|
|
|
|
|
650
|
Ceriatone / Overtone / Re: Overtone Soundclips
|
on: January 31, 2009, 09:38:24 PM
|
Hi Guys,
Another vid from same gig. Nice interaction with the keyboard player on the and of the clip. Hope you enjoy it.
That was beautiful. |
|
|
|
|
652
|
Ceriatone / Overtone / Re: PIN voltages
|
on: January 21, 2009, 02:02:55 PM
|
|
It depends...
I've read on the TAG forum Glaswerks amps have around 185V on V1.
It makes your clean ch sound a tad brighter (in a good way).
If you like what you hear, don't touch it.
|
|
|
|
|
653
|
Ceriatone / Overtone / Re: Pics of completed Overtones
|
on: January 18, 2009, 04:22:53 PM
|
Deep mod is done and it really adds dimension to the tone! Will post pics soon.
I'm thinking about installing the deep switch instead of FET input just like you. I have a question for you. Did you install a resistor on the end of a dropping string to compensate for the missing FET board? If not, what are your plate voltages, did they go up? |
|
|
|
|
654
|
Ceriatone / Overtone / Re: Single G12-65 with the standard OTS amp
|
on: January 12, 2009, 02:26:49 PM
|
Ok, thanks...........+1 on the floorish position. I always strive to do that whenever possible.
Like to have the punchiest sound possible. Unfortunately, as I'm sure you know, sometimes
on small stages, you gotta put 'em a chair and angle up, to be able to hear, etc........
Yes I know what you mean...in this case I just tilt the amp against the wall or something. You could also install Fender tilt back legs. |
|
|
|
|
655
|
Ceriatone / Overtone / Re: Single G12-65 with the standard OTS amp
|
on: January 12, 2009, 11:35:53 AM
|
Are you getting a pretty "full" sound out of it? I.E. enuff bass, etc.......
How does it cut and sound out live in this configuration?
Your combo cab is roughly the size of my 1 12 cab.
It works just fine. It really helps to position the amp against the wall... and don't lift it up from the ground (like a chair or a stand), it helps with the bass response. |
|
|
|
|
658
|
Ceriatone / Overtone / Re: OTS clean channel not very loud
|
on: January 07, 2009, 08:56:18 AM
|
|
My amp tech feels the same about Tungsols.
For some reason these tubes are not very reliable, actually all tubes coming from that particular plant.
He actually prefers JJ, much more reliable tubes.
|
|
|
|
|
|
Show Posts
to keep the forums alive.
