Welcome, Guest. Please login or register.
Did you miss your activation email?
November 22, 2024, 11:38:57 AM
Home Help Search Login Register
News: Ceriatone Forums are up and running!!!
 
Guests please register
Note: If you want to help you can donate to keep the forums alive.



Do you want to advertise on this forum ? Send me a private message.

Amplified Parts
+  Ceriatone Forum
|-+  British Style
| |-+  Plexi Lead, Bass, Superlead
| | |-+  Humming 100watt plexi		 « previous next »
Pages: [1] 2 Go Down Print
Author Topic: Humming 100watt plexi  (Read 17429 times)
d.day
Newbie
*
Offline Offline

Posts: 10


View Profile
« on: June 22, 2011, 10:09:56 AM »
Hi can somebody help!! My 100w plexi is humming with out a guitar plugged in and it's driving me mad. It's worse with the strat plugged in (obviously) It gets louder when the pre amp gets turned up on the bright channel, but my amp guy says it could be anywhere. Any hints??
Logged
ampkits
Administrator
Sr. Member
*****
Offline Offline

Posts: 325


View Profile
« Reply #1 on: June 22, 2011, 04:22:17 PM »

What are the specs? Is it my kit? Trannies? Pics of insides?
Logged
d.day
Newbie
*
Offline Offline

Posts: 10


View Profile
« Reply #2 on: June 23, 2011, 01:02:28 AM »
Hi Nik, Its your 100w superlead plexi. It was rebiased with new power tubes (winged C's) and replaced a pre amp tube. We had dirty/too hot wall power as I'm in Australia. There 's more pics if you need them. The kit was a standard kit apart from a ppmiv.

* DSCF4642.JPG (444.55 KB, 1280x960 - viewed 827 times.)

* DSCF4641.JPG (448.96 KB, 1280x960 - viewed 802 times.)

* DSCF4637.JPG (448.9 KB, 1280x960 - viewed 797 times.)

* DSCF4635.JPG (443.78 KB, 1280x960 - viewed 743 times.)
Logged
d.day
Newbie
*
Offline Offline

Posts: 10


View Profile
« Reply #3 on: June 23, 2011, 01:06:28 AM »
more pics

* DSCF4620.JPG (447.16 KB, 1280x960 - viewed 773 times.)

* DSCF4621.JPG (449.26 KB, 1280x960 - viewed 748 times.)

* DSCF4622.JPG (444.7 KB, 1280x960 - viewed 772 times.)

* DSCF4628.JPG (444.14 KB, 1280x960 - viewed 789 times.)
Logged
d.day
Newbie
*
Offline Offline

Posts: 10


View Profile
« Reply #4 on: June 23, 2011, 01:21:18 AM »
Just a thought...... will additional shielding between the head cab and the chasis help??
Logged
mcinku
Administrator
Hero Member
*****
Offline Offline

Gender: Male
Posts: 1084



View Profile WWW
« Reply #5 on: June 23, 2011, 06:26:13 AM »
Are you sure you don't have a noisy tube in there...
Logged
My website

TW Express build
BM HRM build
Prinzetone build
d.day
Newbie
*
Offline Offline

Posts: 10


View Profile
« Reply #6 on: June 23, 2011, 08:31:46 AM »
Not really. The power tubes have been replaced..... how do I check em??
Logged
mcinku
Administrator
Hero Member
*****
Offline Offline

Gender: Male
Posts: 1084



View Profile WWW
« Reply #7 on: June 23, 2011, 08:40:35 AM »
Well I would start with the preamp tubes you replaced... if you have any tubes lying around and you're sure they are OK, use that and replace one by one to see if your problem goes away.

That would be my first move...
Logged
My website

TW Express build
BM HRM build
Prinzetone build
d.day
Newbie
*
Offline Offline

Posts: 10


View Profile
« Reply #8 on: June 23, 2011, 09:23:29 AM »
Sorry mental blank. I'll try that. Can you check powertubes the same way?
Logged
mcinku
Administrator
Hero Member
*****
Offline Offline

Gender: Male
Posts: 1084



View Profile WWW
« Reply #9 on: June 23, 2011, 09:43:48 AM »
Well I would not replace one by one... cause you need matched tubes.... and when you replace power tubes, you need to rebias as well.
So when you're done with preamp tubes and if problem still persist...then replace all power tubes (use the old ones if that's the only option).
Logged
My website

TW Express build
BM HRM build
Prinzetone build
ampkits
Administrator
Sr. Member
*****
Offline Offline

Posts: 325


View Profile
« Reply #10 on: June 25, 2011, 11:39:31 PM »
Hi,

Yes, bias is definitely needed when you change power tubes.

If not sure, read the chupa manual.

The plexi100 doesnt have bias sockets, but the idea is same - read across the 1R resistor on power tubes.

You should also check your voltages, see if it's in line? www.ceriatone.com/voltage

As for the test, it shouldnt have much noise if set low. But if set high, you should simulate the shield (inside head cab) if testing the amp on the bench. Otherwise, you'd have noise.

This is after assuming your solder work are OK, and connections are correct.

Even if Oz can have 250-260V mains, at low volumes it shouldnt matter much, or for a short while.

Thanks!

nik
Logged
d.day
Newbie
*
Offline Offline

Posts: 10


View Profile
« Reply #11 on: July 02, 2011, 01:46:43 PM »
ok she's back from the amp tech after a having replaced a wire between V1 & V2. All good. I know every amplifier will have a backgroung hum when connected to a box and 1959 will have more hum than a JCM 800..... So how do you remove this from your plexi?? I might put an mp3... Still fkn great amp
Logged
d.day
Newbie
*
Offline Offline

Posts: 10


View Profile
« Reply #12 on: July 09, 2011, 03:47:40 AM »
Hi

Here's the hum recorded off my phone. The ppmiv is at 12 and the hum obviously gets louder as the master vol gets turned up. This is amp only without a guitar and the pre amp is about 1-2 oclock. Can it be trannies?? Its recorded of my phone. Any help appreciated.
* Sound clip 29.mpg (389.45 KB - downloaded 463 times.)
Logged
ampkits
Administrator
Sr. Member
*****
Offline Offline

Posts: 325


View Profile
« Reply #13 on: July 09, 2011, 05:41:11 PM »
Hi

Did the tech do the voltage check?

Reason i stress on it is, in Oz, sometimes wall can go to 260V.  The amp expects 240V.

2ndly, do you already have the shield inside your head cab?

A marshall thats out of cab, or inside a cab without shield, will tend to be noisy.

3rdly - when the tech biased the amp, are the power tubes still matched?

4th - the clip - whats that sound? is it hiss?

5th - when tech installed PPIMV - do make sure the wires go correctly. ie, each side of PI goes to correct pot lug, and correct power tube. Sounds simple, but we have diagnosed several PPIMV mods that had the mistake (hard to see since same color wire used, and they are twisted together).

6th - eliminate sharing of power socket with any other thing. And, if any lights, computers etc nearby, turn em off for a while. See if that changes things.

7th - Again, do check the voltages, and see if inline with given volt sheet.

Hope this helps, let me know..

Thanks!

nik
Logged
SoundPerf
Sr. Member
****
Offline Offline

Gender: Male
Posts: 392



View Profile
« Reply #14 on: July 09, 2011, 10:34:52 PM »
From that sound clip what I hear is not hum, but loads of hiss. Just to clarify, was the PPIMV installed after you got the amp from Nik? When did this noise problem start? I would check the wiring on the PPIMV for sure.

Once again, what I hear is hiss. Did the tech you had it to difinitively rule out any bad tube?
Logged
Chris

Ceriatone HRM 50
w/self built Dumblelator
Avatar 2X12 w/WGS ET-65 & Veteran 30
TC Electronic 2290
2001 PRS McCarty
2010 PRS 513 Swamp Ash
Tacoma JK50C
Seagull S12+
Pages: [1] 2 Go Up Print 
« previous next »
Jump to:  


Login with username, password and session length

Powered by MySQL Powered by PHP Powered by SMF 1.1.12 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!

CeriaTone Forum is not afiliated with Ceriatone Amplifications. The CeriaTone and name, logo and related trademarks and service marks, owned by CeriaTone. , are registered and/or used in the U.S. and many foreign countries. All other trademarks, service marks, and trade names referenced in this site are the property of their respective owners.