Transformer Mounting

captainbackfire
Full Member

Offline

Posts: 113

Transformer Mounting

« on: July 24, 2012, 10:59:19 AM »

Hi! I got my PT from Nik. I notice the screws are substantially closer to each other making a direct fit to the chassis hole quite impossible. Now I'm wondering if the screws are somewhat tightened slightly of from the PT's screw shafts or something and I'm wondering if I can just loosen them up, re align them, and then tighten again making sure they now align with the chassis holes. Is this a bad idea?

Also, Do I remove the nut which holds the PT together and use it to mount to the chassis? Or are there 4 nuts provided in the kit? SHould I leave the nut and mount it like that with another set of nuts inside the chassis?

Thanks a lot. You guys are the best when it comes to helping people in here!
Nico


	Logged

wyatt
Guest

Re: Transformer Mounting

« Reply #1 on: July 24, 2012, 03:29:21 PM »

You do not remove the nuts holding it together.

You use separate nuts to mount it. I prefer KEPS nuts, especially if you are using it as a ground point.

Can't really help you on spacing. Make sure you have the right PT for the chassis.


	Logged

T Wilcox
Sr. Member

Offline

Gender: Male

Posts: 399

Re: Transformer Mounting

« Reply #2 on: July 24, 2012, 10:31:53 PM »

edit:


« Last Edit: July 24, 2012, 10:39:03 PM by T Wilcox »	Logged

Plexi bass 1986 ( build #6 )
Ceriatone Ultra Champ ( build #5 )
TW Express clone ( build #4 )
Ceriatone HRM MK2 ( build #3 )
Ceriatone 2550 ( Build #2 )
Ceriatone OTS FM50 Modern Eagle Mod (Build #1)
EBMM Steve Morse original
50th anniv American Strat

sduck
Full Member

Offline

Gender: Male

Posts: 173

Re: Transformer Mounting

« Reply #3 on: July 25, 2012, 03:23:51 AM »

I used MM transformers on mine - I don't remember which of the transformers it was, but for one of them I had to drill 2 holes in the chassis because the predrilled ones wouldn't work.


	Logged

captainbackfire
Full Member

Offline

Posts: 113

Re: Transformer Mounting

« Reply #4 on: July 25, 2012, 05:23:50 AM »

Thanks wyatt and sduck.

I emailed Nik and he said I need to remove the nuts holding the pt together contrary to what wyatt said (?), then use it to bolt it from the inside. This should re arrange the screws properly and hopefully finally fit perfectly like the pt should. Its made to fit together its an OTS 50 pt. He also advised to scrape the powder coated chassis where it contacts the pt. Is that for heat dissipation only?

Thanks again!


	Logged

wyatt
Guest

Re: Transformer Mounting

« Reply #5 on: July 25, 2012, 05:52:24 PM »

Quote from: captainbackfire on July 25, 2012, 05:23:50 AM

Thanks wyatt and sduck.

I emailed Nik and he said I need to remove the nuts holding the pt together contrary to what wyatt said (?), then use it to bolt it from the inside. This should re arrange the screws properly and hopefully finally fit perfectly like the pt should. Its made to fit together its an OTS 50 pt. He also advised to scrape the powder coated chassis where it contacts the pt. Is that for heat dissipation only?

Thanks again!

Well, so be it. That is contrary to instructions from most transformer manufacturers, they usually want those bell caps left on. Many, like Magnetic Components even lacquer the nuts on.


	Logged

captainbackfire
Full Member

Offline

Posts: 113

Re: Transformer Mounting

« Reply #6 on: July 25, 2012, 10:53:41 PM »

Quote from: wyatt on July 25, 2012, 05:52:24 PM

Quote from: captainbackfire on July 25, 2012, 05:23:50 AM

Well, so be it. That is contrary to instructions from most transformer manufacturers, they usually want those bell caps left on. Many, like Magnetic Components even lacquer the nuts on.

Yes sir I actually read about this. I tried to loosen the nuts a moment ago and the screws can now be adjusted to fit!

Also I wanna make a correction on what I though Nik said. I should just scrape to bare the screw holes on the chassis, not the whole area where the PT contacts the chassis.


	Logged

Pages: [1]

« previous next »

	Welcome, Guest. Please login or register. Did you miss your activation email? November 25, 2024, 04:14:05 AM

News: Ceriatone Forums are up and running!!! Guests please register Note: If you want to help you can to keep the forums alive. Do you want to advertise on this forum ? Send me a private message.