Welcome, Guest. Please login or register.
Did you miss your activation email?
November 22, 2024, 11:05:30 AM
Home Help Search Login Register
News: Ceriatone Forums are up and running!!!
 
Guests please register
Note: If you want to help you can donate to keep the forums alive.



Do you want to advertise on this forum ? Send me a private message.

Amplified Parts
+  Ceriatone Forum
|-+  Ceriatone
| |-+  Overtone
| | |-+  I could use a little more help		 « previous next »
Pages: 1 2 [3] 4 Go Down Print
Author Topic: I could use a little more help  (Read 26539 times)
erwin_ve
Guest
« Reply #30 on: September 01, 2009, 07:35:19 AM »
Quote from: djroge1 on September 01, 2009, 03:58:14 AM
Quote from: parrhasius on September 01, 2009, 03:07:04 AM
What about that 22uF 450V electrolytic cap on the wall near the first tube - shouldn't that be the other way around?

Compare it to this photo from the Ceriatone web site:

http://www.ceriatone.com/images/completeAmpsPic/CTOvertone/board/Leftend2B.jpg

Phil

Bingo! I bet that is a major problem and I don't have to look at your link I see it in the wire diagram.  Huh?  Shocked  Angry Embarrassed  Embarrassed  Embarrassed I can't believe I missed that. I'm going to turn that around and I'll post the results. Thanks.

You are lucky that cap didn't explode!
« Last Edit: September 01, 2009, 07:36:51 AM by erwin_ve » Logged
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #31 on: September 01, 2009, 11:18:37 AM »
Djroge1,

You are close to getting the amp to work now.

When it does, you might want to move the yellow (cathode) and red (plate) wires close to each other. This has a major impact on the notes 'blooming' when you play. Kind of a compressor effect that is part of the signature sound of the Dumble amps.

Looking forward to you getting some sounds thorough!  Smiley
Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
erwin_ve
Guest
« Reply #32 on: September 01, 2009, 11:23:56 AM »
Quote from: djroge1 on September 01, 2009, 04:25:49 AM
. I hear a hum and I get a crackle when measuring V3.
The crackle is normal when measuring your PI(V3). Probably your power amp does work.
Logged
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #33 on: September 01, 2009, 11:48:25 AM »
I guess you mean preamp is not working.

If the power amp is not working, why would djroge1 beable to hear hummmm  Huh?
Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
erwin_ve
Guest
« Reply #34 on: September 01, 2009, 01:06:31 PM »
Quote from: bluesfendermanblues on September 01, 2009, 11:48:25 AM
I guess you mean preamp is not working.

If the power amp is not working, why would djroge1 beable to hear hummmm  Huh?
Can't they read in Denmark? Grin
Logged
René F
Newbie
*
Offline Offline

Posts: 47


View Profile
« Reply #35 on: September 01, 2009, 01:35:19 PM »
Some of us... Smiley

As Erwin said if he can hear crackle then there must be some output through the poweramp... Voltage readings also look fine at the 6L6 tubes
Logged
djroge1
Jr. Member
**
Offline Offline

Posts: 80


View Profile
« Reply #36 on: September 01, 2009, 01:52:34 PM »
I took a quick reading of those previous 10 points and here they are in order - I didn't wait for the amp to really warm up because I'm on my way out the door for work.

455
454
429
318
319
312
174
188
174
191
Logged
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #37 on: September 01, 2009, 03:29:13 PM »
Quote from: erwin_ve on September 01, 2009, 01:06:31 PM
Quote from: bluesfendermanblues on September 01, 2009, 11:48:25 AM
I guess you mean preamp is not working.

If the power amp is not working, why would djroge1 beable to hear hummmm  Huh?
Can't they read in Denmark? Grin


Embarrassed ups!  Cool
Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
hywelg
Hero Member
*****
Offline Offline

Posts: 896


View Profile
« Reply #38 on: September 01, 2009, 06:34:47 PM »
You should now be getting some sound out of it, the voltages are in the right region, though a little low on V1 and V2, though I wouldn't worry about that for now.

Try pluging a lead in to the Power Amp IN socket just to see if the poweramp section is working properly (touch the tip of the other end of the lead). If you do then plug in normally and if you get nothing from either clean or OD then check and re-check your wiring  from input jack up to V3 pin 2 and 7. This is the point at which its helpful to have both the schematic and the layout to guide you whilst checking, but you can do this with just the layout checking every joint that you have made whilst marking them off with a highlighter pen. Any join that looks suspect re-do it.

You have wired your input jacks the right way haven't you?? Wink Have you tried the FET input?
Logged
djroge1
Jr. Member
**
Offline Offline

Posts: 80


View Profile
« Reply #39 on: September 01, 2009, 07:35:36 PM »
I do the power amp In test and recheck my wiring tonight when I get home.

I already checked for continuity from input to V1 pin one and it looks good for both input and FET input. I plugged in a cable and read it from cable to pin one.
Logged
René F
Newbie
*
Offline Offline

Posts: 47


View Profile
« Reply #40 on: September 01, 2009, 07:41:05 PM »
Quote from: djroge1 on September 01, 2009, 07:35:36 PM
I do the power amp In test and recheck my wiring tonight when I get home.

I already checked for continuity from input to V1 pin one and it looks good for both input and FET input. I plugged in a cable and read it from cable to pin one.

If you are testing the FET-input for signal through the amp, then remember to adjust the FET trimmer (on the small board mounted on the side of the chassis). If its turned all the way down, you won't get any signal through the FET input
Logged
bluesfendermanblues
Sr. Member
****
Offline Offline

Gender: Male
Posts: 452



View Profile
« Reply #41 on: September 01, 2009, 08:14:30 PM »
Quote from: djroge1 on September 01, 2009, 07:35:36 PM
I do the power amp In test and recheck my wiring tonight when I get home.

I already checked for continuity from input to V1 pin one and it looks good for both input and FET input. I plugged in a cable and read it from cable to pin one.

Pin one?? you mean pin 2, right?
Logged
Respect for the big guy's work....we're at this part of the forum because of HAD's amps.
djroge1
Jr. Member
**
Offline Offline

Posts: 80


View Profile
« Reply #42 on: September 01, 2009, 08:47:02 PM »
Ooops yes pin 2.


Quote from: bluesfendermanblues on September 01, 2009, 08:14:30 PM
Quote from: djroge1 on September 01, 2009, 07:35:36 PM
I do the power amp In test and recheck my wiring tonight when I get home.

I already checked for continuity from input to V1 pin one and it looks good for both input and FET input. I plugged in a cable and read it from cable to pin one.

Pin one?? you mean pin 2, right?
Logged
djroge1
Jr. Member
**
Offline Offline

Posts: 80


View Profile
« Reply #43 on: September 02, 2009, 12:48:24 AM »
I plugged a cord into the Power Amp In and it appears to be working. Now, I'm going to re-check all of my work up to the points you suggest.


Quote from: hywelg on September 01, 2009, 06:34:47 PM
You should now be getting some sound out of it, the voltages are in the right region, though a little low on V1 and V2, though I wouldn't worry about that for now.

Try pluging a lead in to the Power Amp IN socket just to see if the poweramp section is working properly (touch the tip of the other end of the lead). If you do then plug in normally and if you get nothing from either clean or OD then check and re-check your wiring  from input jack up to V3 pin 2 and 7. This is the point at which its helpful to have both the schematic and the layout to guide you whilst checking, but you can do this with just the layout checking every joint that you have made whilst marking them off with a highlighter pen. Any join that looks suspect re-do it.

You have wired your input jacks the right way haven't you?? Wink Have you tried the FET input?
Logged
Corinthian
Newbie
*
Offline Offline

Posts: 14


View Profile
« Reply #44 on: September 07, 2009, 10:02:26 AM »
Quote from: bluesfendermanblues on September 01, 2009, 11:18:37 AM
Djroge1,

...you might want to move the yellow (cathode) and red (plate) wires close to each other. This has a major impact on the notes 'blooming' when you play. Kind of a compressor effect that is part of the signature sound of the Dumble amps.


This is interesting. Is this something that Nik does in the ready assembled amps?

Looking on the layout, there are two red wired and two yellow lines to V1 and V1. Would you mind marking on the layout which ones should be moved close together? If it is not standard I'd like to do this to mine when it arrives.

Thank you

C~
Logged
Pages: 1 2 [3] 4 Go Up Print 
« previous next »
Jump to:  


Login with username, password and session length

Powered by MySQL Powered by PHP Powered by SMF 1.1.12 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!

CeriaTone Forum is not afiliated with Ceriatone Amplifications. The CeriaTone and name, logo and related trademarks and service marks, owned by CeriaTone. , are registered and/or used in the U.S. and many foreign countries. All other trademarks, service marks, and trade names referenced in this site are the property of their respective owners.