Welcome, Guest. Please login or register.
Did you miss your activation email?
November 26, 2024, 07:11:39 AM
Home Help Search Login Register
News: Ceriatone Forums are up and running!!!
 
Guests please register
Note: If you want to help you can donate to keep the forums alive.



Do you want to advertise on this forum ? Send me a private message.

Amplified Parts
+  Ceriatone Forum
|-+  Ceriatone
| |-+  Overtone
| | |-+  Help Please with overtone 183 build		 « previous next »
Pages: [1] 2 Go Down Print
Author Topic: Help Please with overtone 183 build  (Read 17574 times)
ken swanson
Newbie
*
Offline Offline

Posts: 14


View Profile
« on: June 10, 2012, 12:23:56 PM »
Hello to all. I am having some issues with my 183 build and any help would be greatly appreciated. I am getting some sound out of the amp, but it is very week and sounds like a bad fuzz pedal. I have done the usual checking tubes, and making sure inputs are wired correctly. Have gone through the layout and wiring several times. I plugged a cord in the power amp input, and I am getting a good signal from that.
Here are my voltage readings.
B+ around 458
V1 and V2 high voltage-198v, grids pin 2&7 is 0v, cathodes 1.8v
V3 pin 1 and 6 300v, pins 2 & 7 38v,  and pins 3 & 8 62v
I am assuming my problem is in the preamp section.
I can get more info if needed. Any ideas from the above information?
Thanks to all in advance.
Logged
mcinku
Administrator
Hero Member
*****
Offline Offline

Gender: Male
Posts: 1084



View Profile WWW
« Reply #1 on: June 13, 2012, 10:22:24 AM »
Is your clean ch working OK?

Have you tried replacing V1,V2 tubes?
« Last Edit: June 13, 2012, 10:30:43 AM by mcinku » Logged
My website

TW Express build
BM HRM build
Prinzetone build
ken swanson
Newbie
*
Offline Offline

Posts: 14


View Profile
« Reply #2 on: June 14, 2012, 01:40:50 PM »
The clean channel is doing the same thing. I have changed the tubes also. Do the voltages look to be good?
Logged
mcinku
Administrator
Hero Member
*****
Offline Offline

Gender: Male
Posts: 1084



View Profile WWW
« Reply #3 on: June 14, 2012, 04:25:54 PM »
Voltages look OK to me...

I would say you have a fault at V1, maybe tone stack, maybe input if your power section works fine.
Can you post some pictures?
Logged
My website

TW Express build
BM HRM build
Prinzetone build
ken swanson
Newbie
*
Offline Offline

Posts: 14


View Profile
« Reply #4 on: June 14, 2012, 05:32:30 PM »
Yes I will get some pics up asap. I went back and did some checking, and I now have the normal channel working. I think it was a grounding issue, but now I do not have an overdrive channel. Again, I am getting some signal, but it is very very weak, and extremely distorted. Just to make sure, I went through all the preamp tubes again, and made sure they were all good. So now where do I start to troublehsoot? Pics coming
Logged
mcinku
Administrator
Hero Member
*****
Offline Offline

Gender: Male
Posts: 1084



View Profile WWW
« Reply #5 on: June 14, 2012, 05:55:35 PM »
So V1 is fine, troubleshooting V2 should be even easier...

Let's assume all resistor and caps are fine... I would say you have a wiring issue. Check everything again.... maybe you have a cold solder somewhere. At least you could re-solder all V2 connections.
Logged
My website

TW Express build
BM HRM build
Prinzetone build
ken swanson
Newbie
*
Offline Offline

Posts: 14


View Profile
« Reply #6 on: June 14, 2012, 06:14:35 PM »
Cool. I think I will start there and see what I get. Thanks so much so far with the help. It is greatly appreciated. By the way, I have been checking out your builds, and they are extremely well done!!
Logged
ken swanson
Newbie
*
Offline Offline

Posts: 14


View Profile
« Reply #7 on: June 14, 2012, 08:55:12 PM »
Here are the pics of the amp. Not the order I wanted but oh well.. I know I am missing something stupid.
Logged
mcinku
Administrator
Hero Member
*****
Offline Offline

Gender: Male
Posts: 1084



View Profile WWW
« Reply #8 on: June 15, 2012, 06:02:57 AM »
Can't spot anything from here but just one thing you can check. 100K pre OD pot... check if it's touching chassis... usually there is very tight fit and if you're not careful you can have a short there.
If I were you, I would use my multimeter in continuity mode and check everything for shorts.
Logged
My website

TW Express build
BM HRM build
Prinzetone build
erwin_ve
Full Member
***
Offline Offline

Gender: Male
Posts: 158



View Profile
« Reply #9 on: June 15, 2012, 08:57:15 AM »
Check your cathode resistors at the phase inverter. Those voltages at the v3  grids and cathode are too high.
« Last Edit: June 15, 2012, 09:02:41 AM by erwin_ve » Logged
mcinku
Administrator
Hero Member
*****
Offline Offline

Gender: Male
Posts: 1084



View Profile WWW
« Reply #10 on: June 15, 2012, 09:19:56 AM »
Real 183 had 59V on V3 cathode side... that's not to far from what Ken has.

I don't think he has a problem with PI section.... after all Clean CH  works fine for him.
Logged
My website

TW Express build
BM HRM build
Prinzetone build
erwin_ve
Full Member
***
Offline Offline

Gender: Male
Posts: 158



View Profile
« Reply #11 on: June 15, 2012, 11:11:47 AM »
Quote from: mcinku on June 15, 2012, 09:19:56 AM
Real 183 had 59V on V3 cathode side... that's not to far from what Ken has.

I don't think he has a problem with PI section.... after all Clean CH  works fine for him.

Yeah you're right my bad.. To the OP; Check your wiring for the od trim pot on the back.  measure in Ohms. Sometimes when heated too much, the insulation of the shielded wire is touching the leads.
It is also good to go through the whole schematic and measure each connection. Work yourself from relay Od input to PI input.
Logged
ken swanson
Newbie
*
Offline Offline

Posts: 14


View Profile
« Reply #12 on: June 15, 2012, 10:53:39 PM »
Well I checked all the conections and solder joints with the MM in continuity mode, and all seem to be good. I'm thinking maybe the problem might be in the overdrive relays, or the voltage regulator. Like a dummy a broke a pin off of one of the relays, when I was checking the conections, so can't do anything until I get that replaced. I'll report back, and again thanks for the help so far, and keep it coming if you think of anything. Cheers
Logged
ken swanson
Newbie
*
Offline Offline

Posts: 14


View Profile
« Reply #13 on: June 18, 2012, 09:56:39 PM »
Here is the update Sad. I basically spent the whole weekend going through the circuit, again checking all the voltages, and continuety. Everything is coming up as it should. I rewired V2 just to make sure all the connections were good, and also checked the relay boards to make sure I am getting 12 volts to both of them. I purchased a new relay for the overdrive board, installed it, fired it up and I am getting the same thing. The normal channel works great, barely any output from the overdrive channel unless it is cranked up. By the way, the PAB is working, so it has to be in the overdrive relay board. I moved the relay on the board with a chopstick, while it was in overdrive mode and I got a very loud pop, and then it blew the small 4amp fuse. The 1A fuse is still in tact. I'm beating my head against the wall, any ideas?Could the socket for the relay on the relay board be bad? I checked all my connections on top, and underneath on that board, and all seem to be good. I even reflowed the solder joints on it.
Logged
plasticvonaband
Hero Member
*****
Offline Offline

Gender: Male
Posts: 747


Pickin and Grinnin since 1989


View Profile WWW
« Reply #14 on: June 18, 2012, 11:33:21 PM »
have you checked the wiring on the override switches on the back of the amp? they could be inadvertently wired incorrectly or shorted. also are both switches in the right position?


Gregg
Logged
Overdrive is like peanut butter. Some like it crunchy, some like it creamy.
Bluesmaster 50 2x12 combo and some guitars.
Pages: [1] 2 Go Up Print 
« previous next »
Jump to:  


Login with username, password and session length

Powered by MySQL Powered by PHP Powered by SMF 1.1.12 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!

CeriaTone Forum is not afiliated with Ceriatone Amplifications. The CeriaTone and name, logo and related trademarks and service marks, owned by CeriaTone. , are registered and/or used in the U.S. and many foreign countries. All other trademarks, service marks, and trade names referenced in this site are the property of their respective owners.