Welcome, Guest. Please login or register.
Did you miss your activation email?
November 22, 2024, 10:14:33 PM
Home Help Search Login Register
News: Ceriatone Forums are up and running!!!
 
Guests please register
Note: If you want to help you can donate to keep the forums alive.



Do you want to advertise on this forum ? Send me a private message.

Amplified Parts
+  Ceriatone Forum
|-+  Ceriatone
| |-+  Overtone
| | |-+  HELP! Ceriatone HRM Bluesmaster 100w with 1/2 switch (& JM Mod)		 « previous next »
Pages: [1] 2 Go Down Print
Author Topic: HELP! Ceriatone HRM Bluesmaster 100w with 1/2 switch (& JM Mod)  (Read 16785 times)
DboyBlues
Newbie
*
Offline Offline

Posts: 17


View Profile
« on: December 29, 2010, 03:53:59 AM »
Hello I am new to this forum and long story short, I need help.

So here's the problem...

I received my amp yesterday.  Completely built and tested by Nik @ Ceriatone.  Bought from Him directly.  Came with tubes still in their boxes.  Nik stated that these were the same tubes that they used to test & test my amp for over 15 hours I believe.

I have a 2x12 matchless cab with G12-65's not hooked up to the cab itself but i plug in both @ impedance 4 since they're both 8ohms..

FIRST: my problem was that 2 of the outer power tubes werent lighting up.  Nik suggested that they're loose so i switched all of them up and finally got all of them to light up.. Now what I play, especially the low strings, there's this crazy loud sounds that happens.. It's a popping sound that can sometimes happen really big or sound like a helicopter.. THAT's not normal for an amp (a working one) But I know that maybe something (small or big) must be wrong.  I tried to see what was going on in the back and it looked like the tubes were flashing with every pop...

Are my tubes supposed to turn blue then super hot red? 

Someone please help me!

If you're in SoCal, i'd appreciate some help as well.   

Thanks,

Daniel
Logged
plasticvonaband
Hero Member
*****
Offline Offline

Gender: Male
Posts: 747


Pickin and Grinnin since 1989


View Profile WWW
« Reply #1 on: December 29, 2010, 05:11:01 AM »
have you biased your tubes yet?
Logged
Overdrive is like peanut butter. Some like it crunchy, some like it creamy.
Bluesmaster 50 2x12 combo and some guitars.
DboyBlues
Newbie
*
Offline Offline

Posts: 17


View Profile
« Reply #2 on: December 29, 2010, 05:16:44 AM »
Well shouldn't they already be biased by Nik? He already tried to help me out and he would have mentioned that.  I don't have any tools to do it.. unless you know of another way?? lol. 

Thanks for the reply! I really appreciate it!
Logged
plasticvonaband
Hero Member
*****
Offline Offline

Gender: Male
Posts: 747


Pickin and Grinnin since 1989


View Profile WWW
« Reply #3 on: December 29, 2010, 05:19:40 AM »
they may have been biased at the factory, but it is conceivable that during shipping the tubes may have vibrated enough to make them drift, or the bias knob may have been bumped. it's easy to do, all you need is a digital multimeter. the instructions are on ceriatone's website
Logged
Overdrive is like peanut butter. Some like it crunchy, some like it creamy.
Bluesmaster 50 2x12 combo and some guitars.
DboyBlues
Newbie
*
Offline Offline

Posts: 17


View Profile
« Reply #4 on: December 29, 2010, 06:54:46 AM »
Wow.. I don't know what just happened.. I had a consistency of the popping noise... i kept swapping power tube in different places and what ended up happening was each tube started going redplate.. so I got bored and frustrated and switched out the 12ax7's and got the clean channel to work (crystal clear).. then the OD channel was dead.. swapped again and BAM! Both channels now work! I don't know what happened but i'm wondering if this has happened to anyone else??? 

Thanks for the advice plastic! I'll buy a digital multimeter soon too.. i know i'll need it.
Logged
Tenguitars
Newbie
*
Offline Offline

Posts: 28


View Profile
« Reply #5 on: December 29, 2010, 12:14:10 PM »
If all 4 power tubes are redplating, I would not use the amp until you check the bias.

You can try installing just 2 power tubes in the outer two sockets or the inside two sockets only.
Try it both ways and see what happens. Never install the 2 tubes on the right or left side.
You may find that a tube socket is bad.
Logged
DboyBlues
Newbie
*
Offline Offline

Posts: 17


View Profile
« Reply #6 on: December 30, 2010, 03:54:56 AM »
Man.. IT WAS JUST WORKING LAST NIGHT!!!! IT'S AT IT AGAIN!!! WTHECK!!?

Seriously? Is there anyone in the SoCal area that can help me out?? even if its over the phone??

Much help would be appreciated..

Thanks tenguitars.. I'll give it a try.
Logged
plasticvonaband
Hero Member
*****
Offline Offline

Gender: Male
Posts: 747


Pickin and Grinnin since 1989


View Profile WWW
« Reply #7 on: December 30, 2010, 06:55:15 AM »
Sounds like your tubes may have gotten damaged in shipping. Unforunately UPS is not as gentle as they could be...
Logged
Overdrive is like peanut butter. Some like it crunchy, some like it creamy.
Bluesmaster 50 2x12 combo and some guitars.
DboyBlues
Newbie
*
Offline Offline

Posts: 17


View Profile
« Reply #8 on: December 30, 2010, 07:05:01 AM »
OH I'm so glad they're not! Ok guys.. confession time.. Found out the problem was that I wasn't pushing in the preamp tubes in enough  Embarrassed Phew! What a relief that was!  WOW! This amp is friiigin awesome!!!

Can't wait to get reverb!!!

Thanks for all your help guys! I'll keep this just in case something else goes wrong.
Logged
sduck
Full Member
***
Offline Offline

Gender: Male
Posts: 173



View Profile
« Reply #9 on: December 30, 2010, 06:27:11 PM »
Yes, I found that getting my tungsol 12ax7's into the tube sockets to be really difficult - they didn't want to fit at all at first. I ended up using some kind of rounded tool to work around the edges of the tube sockets to expand them slightly - I just had to do this enough so that I was confident that the tubes had made a good connection on all pins.
Logged
DboyBlues
Newbie
*
Offline Offline

Posts: 17


View Profile
« Reply #10 on: December 30, 2010, 11:42:25 PM »
Yeah.. It was pretty weird but i'm glad it all worked out.  esp with the $$ that was paid.

Cheesy Cheers!
Logged
AdrianJ
Full Member
***
Offline Offline

Gender: Male
Posts: 207



View Profile WWW
« Reply #11 on: January 21, 2011, 02:40:41 PM »
Hi,

Congrats on the new amp...

What's the JM Mod you mention???
Logged
White Rose Guitars
DboyBlues
Newbie
*
Offline Offline

Posts: 17


View Profile
« Reply #12 on: January 21, 2011, 04:36:35 PM »
Hi,

Thanks! it's almost done with it's burn in process.. trying to do it as natural as possible.. when I can't i just put on my iPod.  Some Joe Pass.

I'm not entirely sure but Nik said it's his "specs" to make the amp sound more on the JM= John Mayer side.  Which it DOES!

PM Nik, He'll tell ya.
Logged
212Mavguy
Full Member
***
Offline Offline

Posts: 142


View Profile
« Reply #13 on: January 22, 2011, 03:08:41 AM »
Quote from: DboyBlues on December 30, 2010, 11:42:25 PM
Yeah.. It was pretty weird but i'm glad it all worked out.  esp with the $$ that was paid.

Cheesy Cheers!

Just sayin... if you were to compare Nik's prices compared to other D-style amp builders for something similar you would be more than a little pleased at what you got for what you paid.  I'm VERY thankful for the opportunity to own mine.  Glad things worked out for you!
Logged
AdrianJ
Full Member
***
Offline Offline

Gender: Male
Posts: 207



View Profile WWW
« Reply #14 on: January 22, 2011, 04:06:50 PM »
JM = John Mayer - that's what I thought but didn't want to assume!!
Logged
White Rose Guitars
Pages: [1] 2 Go Up Print 
« previous next »
Jump to:  


Login with username, password and session length

Powered by MySQL Powered by PHP Powered by SMF 1.1.12 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!

CeriaTone Forum is not afiliated with Ceriatone Amplifications. The CeriaTone and name, logo and related trademarks and service marks, owned by CeriaTone. , are registered and/or used in the U.S. and many foreign countries. All other trademarks, service marks, and trade names referenced in this site are the property of their respective owners.