Here is the hardware I have ordered from Hoffman!
I forgot to order the grommets where the PT and OT wires enter chassis!
And will have to find a 2KL pot elsewhere since hoffman did not carry that spec.

EDIT: Forgot to order Power tube hole covers for the 2 unused tubes and LED for pilot light I may change because upon receiving its a little small and will require 180ohm res to work

SPRING FENDER Fender style Tube Clamp 2 1.70 3.40
9 pin PL Fender 9 pin celenex socket and shield 3 2.00 6.00
8 PIN FENDER 8 Pin Fender style ceramic power tube socket 2 1.50 3.00
POT1 Alpha amp pots 2 1Meg Audio 2.00 4.00
POT1 Alpha amp pots 1  2KL 2.00 2.00
POT1 Alpha amp pots 1  250KL 2.00 2.00
POT1 Alpha amp pots 1  500K Audio 2.00 2.00
POT1 Alpha amp pots 1  10KL 2.00 2.00
POT1 Alpha amp pots 2  250K Audio 2.00 4.00
POT1 Alpha amp pots 1  25KL 2.00 2.00
POT PULL CTS amp pots with SPST pull switch 1  1 Meg Audio 8.00 8.00
JACK TIP Bias tip jack 1 1.00 1.00
JACK TIP Bias tip jack 2 1.00 2.00
LED lamp Led lamp Assembly 2 2.00 4.00
FUSE HOLDER F Fender fuse holder 2 2.50 5.00
RECEPTACLE2 Power cord receptacle 1 2.00 2.00
ROTARY 3 Way rotary impedance switch 1 9.50 9.50
TerminalStrip3 3 lug terminal strip 5 0.70 3.50
TerminalStrip5 5 lug terminal strip 5 1.16 5.80
fuse large Standard size Slo-blo fuses 1 0.80 0.80
fuse large Standard size Slo-blo fuses 1 0.80 0.80
Screw4/40x1/4 4/40 x 1/4 Phillips Screw 30 0.06 1.80
Screw4/40x3/8 4/40 x 3/8 Phillips Screw 20 0.06 1.20
Nut Keps 4/40 4/40 Keps nut 50 0.10 5.00
Washer Flat #4 #4 Flat Washer 40 0.05 2.00
WIRE 20GA 20 ga solid core wire - PVC Jacket 20 0.30 6.00
WIRE 20GA 20 ga solid core wire - PVC Jacket 20 0.30 6.00
Shipping Shipping/handling to US 7.00 7.00

Edit: the total cost with shipping from Hoffman is $101.80
See were already saving $$$

For the PT, OT and Choke I will use MrGoldtops suggestion and get them from Magnetic Components.

PT - 40-18073         Fender style
OT - 40-18025        Plexi style OT
Choke - 40-18032    5h choke

Total cost for all iron with shipping = $181.79

Until I have completed this amp I cannot yet guarantee this will be 100% accurate.

Dont know if Nik will continue to supply boards and chassis but I will try to get components into this BOM just in case

If anyone sees any errors please dont hesitate to say so

EDIT: added pot values

Note: if CTS pot is used the chassis and face plate will need to be drilled to accomodate larger size shaft.

Todd

Todd,

I have done two OTS style 50W amps (OTS 50 and OTS FM Mod) using the MC iron. The OTS 50 is up and running and the FM just passed the light bulb test last night.

I like to give credit where due but unfortunately, I forgot the forum member who suggested these components. Point being, others have used these trannies before me.

Appreciate your list.
Rick

I will probably share cabs with my FM for a little while to save some $

This guy makes some nice cabs, he can do more than what you see there too just ask him. Oh yeah cheaper than anyone else I've found also.
I had him make me a 2 rock style head cab ( little taller than d-stle, but fits my c-lator as well) then he also built me a d-style 2x12.

I paid $190 for head cab and $235 for 2x12 shipped!
U.S. only though

http://ceriatoneforum.com/index.php?topic=3454.0

I just got the heirloom style cab from gabkits for my 2550 and man it was almost $90 more and I feel like its gonna break its so flimsy.

Todd